14520 NE 91st Ct., Redmond, WA 98052 ph: 425.883.7000   fax: 425.883.8080   e-mail: sales@hiltonvalve.com

		Ordering Information
		When ordering, please specify the complete figure number, including type of seat, special features (if any), and material code. Also specify packing and seal ring materials. Basic Figure Number ( i.e: H-201-B) identifies types of valve Examples: H-200: Wafer Knife Gate Valve H-110: Wedge Gate Valve H-900: Angle Disk Check Valve Last Digit Indicates Type of Seat ( i.e: H-201-B) 0: Metal Seated (H-200, H-110, H-900) 1: Single Resilient Seal (H-201, H-111, H-901)		Example; H-201-B-T304 Bonneted Knife Gate Valve, wafer face to face, resilient seated, with 304 stainless steel wetted parts and carbon steel flanges and stiffeners. Additional Features, if required ( i.e: H-201-B ) Knife Gate Valves   B: Bonneted   V: Vee Port for Throttling   R: Special Gate Wedging for Reverse Flow Service   W: Removable Wear Resistant Seat Wedge Gate Valves   M: Special Construction for Marine Service   N: Narrow Face to Face Design Material Code ( i.e: H-201-B-T304 ) Alloys shown are typical, valves are available in any weldable alloy. "Carbon Steel" refers to ASTM A-36 Commercial Grade Carbon Steel. On request, ASTM A-516 Pressure Vessel Grade Carbon Steel can be furnished.
		Alloy Trim: Carbon steel body with alloy seat, gate and stem. (Note: On bonnetless knife gate valves, the stem will be 304 SS, regardless of trim material, unless otherwise specified.)   CS/304: Carbon steel body with 304SS trim   CS/M: Carbon steel body with Monel® trim Alloy Wetted Parts: All wetted parts are alloy material; external flanges and stiffeners are carbon steel.   T304: 304 55 wetted parts with carbon steel flanges and stiffeners   A20: Alloy 20 wetted parts with carbon steel flanges and stiffeners Solid Alloy: Solid alloy construction, except for handwheel and stem nut assembly.   ST3l6: Solid 316 SS construction   SHC: Solid Hastelloy C® construction Stellite® Hardsurfacing: For abrasive service, or to prevent galling, Stellite® hardsurfacing can be furnished.   T3l6/S: 316 SS wetted parts with partial Stellite® hardsurfacing. For moderately abrasive service - hardsurfacing on edge of seat, on leading edge of gate and on gate wedging surfaces.   T316/FS: 316 SS wetted parts with full Stellite® hardsurfacing. For severe abrasive service - hardsurfacing in inlet and outlet ports of valve, on leading edge of gate and on gate wedging surfaces.	Typical Alloys T304 (T316, T317):    Type 304 (316, 317) Stainless Steel T304L (T3l6L, T317L) Low carbon stainless steel FE: Ferralium® A20: Alloy 20 M: Monel® 1625: Inconel 625® HC: Hastelloy TI: Titanium IG: Fiberglass
		Packing In keeping with the current concern regarding the use of asbestos products, we have available a large assortment of non-asbestos packings, including the following: Waxed Flax - general oil and water service, to 150oF. TFE/Synthetic Fiber - mild acids and alkalis, to 500oF. TFE/Keviar® - abrasive slurries or strong chemicals, to 500oF. Pure TFE - food service or severe chemicals, to 500oF. Inconel/Fiberglass - high temperature service, to 1000oF. Braided Ceramic - high temperature service to 2000oF. Resilient Seal Materials Available in a wide variety of elastomers, including the following: Buna N - general oil and water service. to 2500F. Neoprene - general service, including a broad range of chemicals, to 250oF. White Neoprene - used to prevent color contamination, to 2500F. TFE - food service or severe chemicals, to 500oF Viton® - wide range of chemicals or high temperature service, to 400oF. Polyurethane - abrasive service, to 200oF; not suitable for acids, ketones and chlorinated hydrocarbons. Ethylene Propylene (EPR) - water, oil and certain phosphate ester based fluids, to 250oF; not suitable for petroleum lubricants and solvents. Pressure Ratings Standard 2" thru 24": 150# CWP (Cold Working Pressure) Above 24": 50# CWP. Other pressure ratings are available, including ANSI and API.
		return to products profile | products | showcase | contact us | home